Search results

=Projects= |<DPL>category = Projects done</DPL>

[[Category: Projects]]

[[Category: Projects done]] This supposingly saves some space when doing AVR based (THT) projects. The ISP port takes more space than the MCU itself, so...

[[Category: Projects]]

General idea is to beat [[CBA]]. Contenders will do their electronics related projects and document them on the Electriki. Yes, this fits the "What do you build?" # One cannot apply projects for a upcoming month's account.

[[category:projects]]

...ojects]] in one place. So there's some (rather little) chance of some nice projects/howtos portfolio growing up in here in few weeks/months/years/centuries.

[[Category: Projects]]

[[category:projects]] For now, the attemts to make a gainclone can be seen on [http://www.bc547.dk/projects/GainCloneProject.html www.bc547.dk's page about the daily life of the gainc

[[category:projects done]]

[[category:projects]]

...if you're editing a page for one of your [[:Category:Projects|electronics-projects]], it might be a good idea to start your page with... [[category:projects]]

[[Category: Projects done]] ...our beginings in the electronics field I decided to share one of my first projects - a '''four channels stereo audio mixer'''.

[[Category: Projects]] ...voltages. Also some mosfets to allow PWM LED. Only a test board, gonna be done again in short while.

[[category:projects]]

...ng micro-controller based solution with upload memory/hard disk to run off projects whilst in standalone mode (dependant on costs). [[Category: Projects]]

[[Category: Projects done]] Want to use high current load outputs in your projects? Here I present you the easiest way of doing it.

[[category:projects done]]

[[Category: Projects done]]

[[Category: Projects]]

[[Category: Projects done]]

[[category:projects done]] ...l application note from Atmel describing how to do this. Atmels example is done in assembler and is fault tolerant, but it's difficult to understand. By do

[[Category: Projects]]

[[category:projects done]] ...s temperature using a terminal-emulator or script; basic error-checking is done so that parity-/communication-errors and 'missing sensor' issues are indica

...ust wont cope with, or simply to keep your coffee warm on those late-night projects. ...it does the job. There is no actual controller on this board, that will be done on a separate board, this just supplies the +12v for the relay, +5v for the

[[Category: Projects done]] ...times flashes, and more and more often nowdays - LEDs. Since LED makes the projects cool, guess what I went for to try out this technique as well...

[[Category: Projects done]] LED is very often used in various projects. There are many types with various colours, shapes, sizes. But what if none

[[category:projects]]

[[category:projects done]]

[[Category: Projects]]

[[category:projects done]] ...cks. I believe it to be causing high-ohm connections where there should be done.

[[Category: Projects done]]

[[category:projects]]

[[category:projects done]] As this is not optimal in regards to the electrical bill, something had to be done.

[[category:projects done]] The time of sample was done by reading the clock at at certain time based on the time on the TV. The de

[[category:projects done]]

[[category:projects done]]

[[Category: Projects done]] ...FR2705 MOSFET's in my drawer for a while now and I like to use those in my projects. I have 2.1m long cabinets hanging in my kitchen and the light source here

[[Category: Projects done]] ...is a good thing to have in every house. Since I have the hardware already done, and the PC is running quite often, too... The question should be why NOT t

[[category:projects done]] ...w''' to select from these wonderful games. It turned out that selection is done by ''turning the console off, then on again''. How original. How weird.

[[category:projects done]] Not very pretty. The 5 / 3.3 V target-voltage selection was done through (de)soldering a green wire-bridge. This dongle can do [http://www.a

[[category:projects]] ...of a BC547 and a BD139 ( any medium power NPN will do ). Assembly will be done shortly(tm), with the Molex connectors, for both input and output supplied

[[category:projects done]] For reference, fade-in and -out and normalisation were done using:

[[category:projects done]] Its simple, its Goofy and probably not the way most of you would have done it, but in the process of this I wrote my first scrip in Linux ever :-)

[[category:projects done]] During the replacement of the caps, a measurement of ESR was done on each old and each new capacitor:

[[category:Projects done]]

[[category:projects]]

[[category:projects done]] ...rflow), the actual changing of tones/volume by setting timer-registers was done from the main loop in the code.

...for me when i was using large IDEs (probably some bitbanging fun has been done there, but really [[CBA|CBA]] to investigate on it), it seems to not be tha [[Category: Projects done]]

[[Category: Projects]]

[[category:projects done]]

[[category:projects done]]

[[category:projects done]] ...puts See [[:Image:Michai_014_logic.jpg|Fig.0]] for an idea. Schematics are done using [http://www.geda.seul.org/tools/gschem/ gEDA's gschem], should you wo

[[category:projects done]] [[image:Michai_032_board_antenna_led.jpg|thumb|'''Fig.10: done soldering.''' Used a can of paint to wind a nice 10cm diameter antenna, sol

[[category:projects done]]

[[category:projects done]] ...toy-board. The funny thing is that when it's finished and toying has been done, it'll totally useless.]]

[[category:projects done]] ...t [https://en.wikipedia.org/wiki/Domain-specific_language DSL]s, as I have done on a few occasions. The DSL used here and elsewhere ''is itself'' Tcl, expl

[[category:projects done]]

...ter work was discussed, he continued by talking about his many electronics-projects he had made, in an almost apologetic way for 'wasting my time'. I didn't mi ...t it was me who robbed the bank, but they never caught me, the getaway was done in my old Nissan Primera (R.I.P).